ALWAYS INNOVATING, NEVER DUPLICATING

 
 
 
 

MFC 2.0" Lift Kit

2014 - 2018 Cherokee KL Lift Kit Overview


The MFC Lift kit for the 2014 - 2018 Cherokee KL is comprised of top quality parts machined out of Billet T-6061 aircraft grade aluminum for the finest fit and finish to raise your Jeep to it's full potential and is patented. With careful consideration in mind relative to body geometry, CV angles and drive-line components, this lift kit improves looks and performance for all trim levels of the KL platform. 


The MFC Lift Kit fits Cherokee KL all trims:

  • 2014 -2018 Jeep Cherokee FWD
  • 2014 -2018 Jeep Cherokee Sport AD1/AD2
  • 2014 -2018 Jeep Cherokee Latitude AD1/AD2
  • 2014 -2018 Jeep Cherokee Limited AD1/AD2
  • 2014 -2018 Jeep Cherokee Trailhawk


Understanding which drive-line you have

















Our Level 1 Kit includes the following components and gives your FWD, AD1/2 & Trailhawk a 2 inch lift:

  • 4 adjustable billet aluminum front strut spacers
  • 2 billet aluminum rear spring spacers
  • Factory bolts and nuts along with set screws for correct clocking of the rear spacer


Why lift your KL with our kit?


With this lift, you are capable of fitting 32" BFG 255/75R17 KO Mud-terrian tires with no wheel hub spacers as shown in the picture above. This will net you a full 3.25"" body lift over factory Trailhawk clearances. This is the only lift that retains all aspects from the factory. MFC's lift retains true clocking position of rear coil springs, reinforces the factory strut when elongated to prevent any lateral forces and NO DRILLING of any suspension parts to make it fit! 100% bolt on!


The following can be a result when lifting your Cherokee with the cheaper options out there. As you can see in the picture, the strut was not reinforced. This is guaranteed to NEVER happen with MFC lifts. Take note of the bend bulge where the strut meets the knuckle. The MFC lift closes this gap, and reinforces all physics of forces transmitted from this area back into the knuckle.



















To fit a 32" tire, minor trimming of plastic and a pinch weld is necessary. Please click HERE to see how it is accomplished. (Courtesy of Seven Slot Syndicate)


Geared towards both novice and true gear-head, the MFC Lift not only is the first ever developed lift for the KL platform, but is the ONLY one you need to purchase. MFC Offroad guarantees all aspects of the MFC Lift as to never fail, break, or crush under the weight of the vehicle, under normal use both on and off road.


*** THE MFC OFFROAD 2.0" LIFT KIT WILL NOT VOID YOUR JEEP WARRANTY ***


As per Mopar's Jeep Cherokee warranty guidelines, a lift of 2" or less does not void your warranty. This paperwork is available for download below. 


Please be sure when purchasing to note in the comments section you preferred choice of free upgrade. We offer raw billet aluminum and black satin hard coat anodized. These are a  courtesy to give MFC Offroad customers that custom feel to a custom part.


For customers who have a Sport model or have the ADI suspension and want to fit larger wheels, it is recommended to swap the rear trailing arms with Trailhawk versions. This is rather inexpensive and ensure the ability to run larger tires after lifting your Jeep. The following part numbers are for your reference:


Right Trailing Arm - 68155228AF ~ $125.00

Left Trailing Arm - 68155227AF ~ $125.00


These can be found here: www.eastcoastmoparts.com


*** CLICK THE LOGOS BELOW FOR INSTALLATION INSTRUCTIONS, CAMBER ADJUSTMENT PROCESS WHEN COMBINED WITH DOBINSON'S SUSPENSION OR WARRANTY LOGO TO SHOW PROOF OUR LIFT DOES NOT VOID YOUR WARRANTY ***

 
 
 
 
 
 
 
 
 
 
 
 

Instructions

Warranty Info

Camber Adjustment

Configuration

ADI

ADII

Trailhawk

FWD

No Knob

Knob | No 4WD Low

Knob | 4WD Low

Knob | 4WD Low & Rear Lock